BA - Steven - She's gone :(

**Posted:** Thu Jul 22, 2010 11:50 pm

You just need to take away the rust, that will look so much better! Tough, its a nice car!

**Posted:** Fri Jul 23, 2010 12:53 am

Really like the skirts Steven :thumbright:

**Posted:** Fri Jul 23, 2010 12:56 am

Looks great fluffy!

**Posted:** Fri Jul 23, 2010 1:25 am

Ahhhhhh I miss Kirrrrrra, did you respray them both then?

**Posted:** Fri Jul 23, 2010 9:49 am

Cheers all

I keep looking out at the car, well not just now as i am getting some of the last stuff done for preperation for its MOT.

tonz13 wrote:

Ahhhhhh I miss Kirrrrrra, did you respray them both then?

nope! The front lip needs resprayed along with part of the door and arches when they get tackled for the rust so i think i am gonna do everything at once.

**Posted:** Fri Jul 23, 2010 12:17 pm

Looking much better Steven :thumbright:

, really wish id had the money to buy them from Tonz :lol:

**Posted:** Sat Jul 24, 2010 2:25 am

These truly are my favourite side skirts out of all that i have seen. Over 60 mods to the car now and i think the HID's, side skirts and induction kit are my favourite three mods of all.

**Posted:** Sun Jul 25, 2010 9:31 pm

white or florescent yellow would like cool

like another green ba with jdm side lights on this page..:P

**Posted:** Wed Aug 18, 2010 4:12 pm

excellent work

I´m Impressed

**Posted:** Wed Aug 18, 2010 5:38 pm

cheers matey

**Posted:** Thu Sep 16, 2010 3:59 pm

Started my prep for the Crail Quarter mile drag strip.

Ported and Polished throttle body fitted.

The P&P one in my hand ready to be switched over

Old and new side by side

**Posted:** Thu Sep 16, 2010 4:20 pm

Nice one fluffy

Noticed any real difference? This is on my to-do list :roll:

**Posted:** Thu Sep 16, 2010 5:38 pm

Not had a chance to open her up but so far i have noticed a HUGE improvment on low revs (2000-4000) rpm, pulls a lot more. I think i get a few MPH more out of the gears now too but as i have said not 100% sure of other improvements. Will update everyone as i find out.

**Posted:** Thu Sep 16, 2010 5:42 pm

Awesome

Getting my dremel out later then

**Posted:** Thu Sep 16, 2010 6:49 pm

you will only get a bit more in the gears if the power output is raised in the rpm which it should do

**Posted:** Thu Sep 16, 2010 8:02 pm

I have taken it out for a more spirited drive, definately a bit of difference.

**Posted:** Thu Sep 16, 2010 8:08 pm

did you gain much RPM at the top?

**Posted:** Thu Sep 16, 2010 8:13 pm

Awesome looking, needs polishing :lol:

**Posted:** Fri Sep 17, 2010 2:13 pm

A guide has been put up here for y'all

http://www.club323f.com/club323f/forum/ ... hp?t=41864

**Posted:** Fri Sep 17, 2010 8:43 pm

looks good mate just like my rover's :P
(ill take a pic)
youll only get more mph in the gear if the revs into the gbox are more...
its a direct ratio from engine speed to gbox speed then from gbox speed to diff speed which is wheel speed :P

**Posted:** Thu Oct 21, 2010 11:32 pm

Car is going in the body shop on Saturday at 1pm in prep for Crail.

NERVOUS.

**Posted:** Fri Oct 22, 2010 12:49 am

you left this to the last minute like i usually do

**Posted:** Fri Oct 22, 2010 12:54 am

What you getting done fluffy?

**Posted:** Fri Oct 22, 2010 9:28 am

i think i know

**Posted:** Fri Oct 22, 2010 9:29 am

Breasts!

Good decision, Steve!

**Posted:** Fri Oct 22, 2010 10:22 am

Breasts?!?! I wanna see

**Posted:** Fri Oct 22, 2010 10:25 am

**Posted:** Fri Oct 22, 2010 10:37 am

Sorry, I couldnt resist

**Posted:** Fri Oct 22, 2010 10:53 am

DMS wrote:

Sorry, I couldnt resist

ffffffffffuuuuuuuuuuuuuu

**Posted:** Fri Oct 22, 2010 11:52 am

Not breast no, as Paul said i have decided to whack the roof off.

Forum rules - Please read!

BA - Steven - She's gone :(

Who is online