Club323F
http://www.club323f.com/forum/

Xedos 6 intake manifold
http://www.club323f.com/forum/viewtopic.php?f=3&t=48299		 Page 1 of 1
Author:  Stuz [ Fri Nov 11, 2011 6:25 pm ]
Post subject:  Xedos 6 intake manifold
Does anyone know anything about these manifolds?

I was at my scrappy today and found one and they look incredibly like the KLZE Manifold. . .I thought it was at first glimpse :dontknow: (see picture)

Image

Image

I'm now wondering if they have the same/similar flow properties and if they do would it be beneficial fitting one to the BA ?

Any info anyone has on these would be grateful :)

Stu
Author:  DMS [ Fri Nov 11, 2011 7:00 pm ]
Post subject:  Re: Xedos 6 intake manifold
I'm sure the Xedos engine has a lot in common with the V6 from our cars.
Author:  Stuz [ Fri Nov 11, 2011 7:25 pm ]
Post subject:  Re: Xedos 6 intake manifold
Yeah, I'm sure the block and heads are exactly the same, it's just this intake manifold I'm rather interested in :)
Author:  DMS [ Fri Nov 11, 2011 8:23 pm ]
Post subject:  Re: Xedos 6 intake manifold
Do you think it you were to offer it up to an 'F' head it would bolt on without many problems?

The bhp is the same as ours for the Xedos 2.0 V6 and they did a 1.6 as well. The 2.0 used was the KF engine
Author:  Stuz [ Fri Nov 11, 2011 8:57 pm ]
Post subject:  Re: Xedos 6 intake manifold
It should bolt on directly with no problems :D
Author:  andym323 [ Sat Nov 12, 2011 10:51 am ]
Post subject:  Re: Xedos 6 intake manifold
Far as I know its the same engine, actually, the Xedos 6 shares its chassis floor plan with the BA F, unlike the larger Xedos 9 which shares its chassis with the Millenia.

Don't forget the Xedos 6 is by definition a rather soft executive saloon car, this is emminently demonstrated by the tweed interior!!!!! ;) So if anything the Xedos 6 manifold would probably be a softer tune than the F one :)
Author:  Stuz [ Sat Nov 12, 2011 5:13 pm ]
Post subject:  Re: Xedos 6 intake manifold
Hmmmmm.......I see where you are coming from andy but why is it like the KLZE manifold ? there must be a reason :lol:
Author:  DaveMc [ Sat Nov 12, 2011 6:31 pm ]
Post subject:  Re: Xedos 6 intake manifold
Lack of space in the engine bay i would assume
Author:  andym323 [ Sun Nov 13, 2011 11:26 am ]
Post subject:  Re: Xedos 6 intake manifold
That'd be my guess too :D
Author:  fastmike [ Sun Nov 13, 2011 11:21 pm ]
Post subject:  Re: Xedos 6 intake manifold
Having fitted a Xedos V6 engine to my last BA the manifolds do swap, but the pipes, sensors and what not won't fit or reach when put in the 323F engine bay... easily. Not to mention the throttle body goes straight to the battery in a 323f orientation ;)
Author:  andym323 [ Mon Nov 14, 2011 1:20 am ]
Post subject:  Re: Xedos 6 intake manifold
I guess space s indeed the answer then :)
Author:  lewp91 [ Mon Nov 14, 2011 3:15 am ]
Post subject:  Re: Xedos 6 intake manifold
would be nice to get some internal measurements though guys if you can! might be worth the few ponies..
Page 1 of 1 All times are UTC [ DST ]
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/