| Club323F http://www.club323f.com/forum/ |
|
| inttake pipe http://www.club323f.com/forum/viewtopic.php?f=3&t=23884 |
Page 1 of 1 |
| Author: | kieranv6 [ Mon Feb 11, 2008 8:02 pm ] |
| Post subject: | inttake pipe |
i am going to make one myself as i cant find one for my broken one. but if i make one out of piping what do i do with the pipe that come of the standed pipe? and what is it aswell. its about inch wide round tube, it right next to the the metal to rubber conection. |
|
| Author: | Dazp1 [ Mon Feb 11, 2008 8:27 pm ] |
| Post subject: | |
It's for the valve cover vent pipes. |
|
| Author: | kieranv6 [ Mon Feb 11, 2008 8:40 pm ] |
| Post subject: | |
so what can i stick on end of it then? |
|
| Author: | griff88 [ Mon Feb 11, 2008 9:10 pm ] |
| Post subject: | |
if its the pipes that i think it is then you can but little filters that go on the end of them. lok like little induction kits. cool as in my book. griff |
|
| Author: | kieranv6 [ Mon Feb 11, 2008 11:32 pm ] |
| Post subject: | |
http://cgi.ebay.com/ebaymotors/NEW-12mm ... enameZWD2V these things? |
|
| Author: | Matt [ Mon Feb 11, 2008 11:41 pm ] |
| Post subject: | |
post ford has one pipe coming off - can indeed just be replaced with a breather filter on the engine side pre ford has2 pipes - the same as above + one other pipe which i have no idea what it does, where it goes or how to get around it so hopefully you have the post for version 
|
|
| Author: | kieranv6 [ Mon Feb 11, 2008 11:57 pm ] |
| Post subject: | |
i only got 1 pipe i think. well i sure i have. so breather on there some alloy pipe from engine to air flow then filter. sounds good. my flat spot from my tear in the rubber doing my head in. |
|
| Author: | Mark.T [ Tue Feb 12, 2008 8:54 am ] |
| Post subject: | |
The pre-ford's extra pipe goes to a small resonator box to help throttle response or something. Ford ditched it, though no-one seems to have noticed a difference. Maybe it's effects have been handled elsewhere - ECU maybe. Mark |
|
| Author: | nat1979 [ Sat Mar 08, 2008 12:36 pm ] |
| Post subject: | |
so when you connect the breather filter to the pipe on the engine side what would i use to seal the hole on the intake pipe (post ford)? |
|
| Author: | kieranv6 [ Thu Mar 13, 2008 7:14 pm ] |
| Post subject: | |
right done mine i will take pic and show you what i done. i made it all myself in work |
|
| Author: | A L 3 X [ Thu Mar 13, 2008 7:25 pm ] |
| Post subject: | |
[quote="Mark.T"]The pre-ford's extra pipe goes to a small resonator box to help throttle response or something. Ford ditched it, though no-one seems to have noticed a difference. Maybe it's effects have been handled elsewhere - ECU maybe. Mark[/quote] are u talkin about the reso box in the wheel arch which most people remove or a different one? |
|
| Author: | ph3n1x [ Sat Mar 15, 2008 1:52 pm ] |
| Post subject: | |
mark t means the little box in between the intake piping, the carter vent pipe and the idle air intake.the first 2 make a T junction to the idle air. After Ford took over they ditched that and added a sort of Y connection in between and removing the mini box |
|
| Page 1 of 1 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|