Club323F :: View topic - ArtistKS's 1996 1.5 BA

Club323F http://www.club323f.com/forum/

ArtistKS's 1996 1.5 BA http://www.club323f.com/forum/viewtopic.php?f=14&t=61103	Page 1 of 2

Author:	ArtistKS [ Tue Jul 02, 2019 8:07 pm ]
Post subject:	ArtistKS's 1996 1.5 BA
Never actually posted my lantis here, fellow user Serena urged me to and here it is. My 1996 1.5 323f BA Has around 63000km currently, had around 57000km when I bought it almost a year ago. Not much really to say. It's in amazing condition, the exterior and interior, low mileage aswell as I stated. Love it so much. Since I got I haven't done much to it although there are a few things I want to do. I converted the headlights except the brights with an HID kit, the bumper lights with leds. Attached an exhaust tip to make the rear look abit nicer. Replaced the air filter with a k&n panel. Most recently I made a lip out of a rubber strip off ebay for the front bumper. There are more things I'd like to do, such as lower it slightly, install a cold air intake (regardless whether it's worse for power or not ), install a front strut bar, maybe get some sort of performance exhaust, replace the aftermarket stereo with a double din unit. So far things like that. Would love to hear what you guys have to say or if anyone has any questions

Author:	SerenaJ [ Tue Jul 02, 2019 9:19 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
Nice one, Kristov! Though, pick up the photo's "BB code" on Imgur instead of the straight link, and the image will show up directly The one with the "img" tags. S

Author:	ArtistKS [ Tue Jul 02, 2019 9:46 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
Oh haha thanks, was wondering why it wasn't showing up, thanks

Author:	smurf182 [ Tue Jul 02, 2019 10:36 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
Very nice indeed, id recommend a drop of around-40mm, still get all the comfort and the drive feels so much nicer too. And with a brace added too it will be much more responsive too. Id highly recommended a rear strut brace too

Author:	maZZda [ Wed Jul 03, 2019 11:35 am ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
Nice looking F, i'm liking the numberplate too. Keep it tidy!

Author:	ArtistKS [ Wed Jul 03, 2019 3:04 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
Haha thanks, yea I'm glad one of the previous owners chose that. I forgot to mention, I'm thinking of naming it but I don't really know what to, with the number plate starting with LRT. Any ideas? Preferably female (idk why )

Author:	smurf182 [ Wed Jul 03, 2019 4:16 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
Dont worry too much about naming the car, it will choose its own name, my first F had terrible steering, i called it dancer, the second was built from many cars, i called it womble, etc. This new one is still to be named, though after a long drive it got covered in bugs....im tbinking this one may be called Bugsy

Author:	brucey76 [ Wed Jul 03, 2019 6:52 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
I miss my F rip little blue

Author:	da2el [ Sat Jul 27, 2019 1:41 am ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
I love the color Nice touch the license plate With that wheel size you really need to lower it a bit

Author:	ArtistKS [ Sat Jul 27, 2019 9:16 am ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
Yea I want to get eibach lowering springs for it but can't afford the 150euro for them plus however much a mechanic would charge to fit them really right now, especially since I'm a student but I will be getting them at some point, hopefully soon

Author:	da2el [ Sat Jul 27, 2019 9:05 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
150 only? I think I paid more in Portugal for the Eibach -30mm Installation it's sad it is something we can't easily do at home

Author:	smurf182 [ Sat Jul 27, 2019 9:26 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
swapping springs is pretty straightforward if you have the right equipment, spring clamps and follow the guide from on here (guides section BA). just be aware of the possibly dangers and work carefully and all will be good

Author:	maZZda [ Sat Jul 27, 2019 11:01 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
Besides, rear ones didn't even need a spring clamps, you can easily push them with your body weight and that's enough to put or remove the nut on the strut. Front ones are another beer! they need clamps.

Author:	SerenaJ [ Sat Jul 27, 2019 11:47 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
As the guys say, switching is a straightforward process, and you only need a jack and axle stands and basic tools. You could do it yourself, although it's easier with someone to help. Me and AndyM swapped suspensions between my car and his, in a car park, with just a jack and stands (I had his shocks and springs, he had my racing coilovers - it's on my V6 thread). However getting the shock absorber off the hub can be heavy work, especially if the nuts have never been undone. Also, unless you can undo your rear droplinks, you will need to cut them off and fit a new set. When you change the front, be very careful not to let the hub drop, and the driveshafts fall out!! When you do the job, it's a good time to check inside the suspension turrets for rust, and to treat inside the top of the turrets while the shock absorbers are out. Inspect the top mounts as well, and replace them at the same time if they're looking bad. If you switch to coilovers you don't even have to take the spring off the shock absorber, just drop the entire leg + spring out of the car, in one piece, and replace the entire thing with the coilover S

Author:	ArtistKS [ Sat Sep 21, 2019 9:27 am ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
Just thought I'd add some stuff to show what I've done so far. The first thing I changed when I got the car were the number plate lights, ordered LED replacements off ebay and was happy with the result. I also changed the interior light to an LED aswell as the light in the boot An HID kit was installed for the headlights which a fellow member generously gifted me and also changed the bumper lights to LEDs. The most recent thing I done, last week, was take out the aftermarket stereo that the previous owner installed, aswell as remove the cubby hole above it and install a double din unit. I'm going to try and install a reversing camera soon, I also have a few more things planned later on in time

Author:	maZZda [ Sat Sep 21, 2019 1:15 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
Nice mods!Keep up the good work on the car!

Author:	ArtistKS [ Tue Sep 24, 2019 10:37 am ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
After a whole day of fiddling yesterday I finally got the reversing camera installed. Had to take off all the trim of the boot gate and also of the boot and some trim on the right hand side rear side to manage to route the cables properly and find the wires I had to splice into (which I didn't manage to find). I followed the wires from the reversing light to the harness where it connects with the body and then followed the wire I thought was the correct one into the body but apparently it wasn't, couldn't find any diagrams anywhere either so I just spliced into the positive and negative of the reverse light and ran wires directly from it and ran it with the factory harness through the rubber conduit into the body and under the headliner and into the boot to connect to the camera which I mounted using zip ties and wood, mounting the wood to the crash bar of the rear bumper (to avoid drilling into the bumper). I then ran the video cable to the front of the car going through the trim which was already off and then running it along the rubber along the windows, down the right hand side of the dash, under and into the centre console. Works a treat

Author:	SerenaJ [ Tue Sep 24, 2019 6:14 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
Nice job!!! I might seriously consider that for Sundance ... S

Author:	ArtistKS [ Tue Sep 24, 2019 6:34 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
It's well worth it but it's one hell of a job. If you decide to take up the job feel free to ask me if you're stuck on anything

Author:	ArtistKS [ Sun Oct 06, 2019 2:53 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
Today I installed the V6 splitter on my 1.5 Big thanks to hughie for providing the splitter Had to put screws into the bumper but oh well, worth it

Author:	SerenaJ [ Tue Oct 08, 2019 1:00 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
Nice job! What's next? S

Author:	ArtistKS [ Tue Oct 08, 2019 7:37 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
I've got a few things ordered on ebay which will arrive between november and december. Remote central locking, mazdaspeed valve caps, mazdaspeed door latch covers and a usb thing instead of the cigarette lighter. I'll be changing my wheels at some point either at the end of the year or sometime next year aswell as get a dual exit exhaust. Those are the plans for the near future, I do have a long list of things I'd like to do though

Author:	ArtistKS [ Fri Nov 08, 2019 9:51 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
Replaced the cigarette lighter with a 2 port usb hub. and the big boi, a mazdaspeed front strut bar Very happy with that Next up, remote central locking and possibly either lowering springs and dual exit exhaust amongst other things.

Author:	lantisv62500 [ Sun Nov 10, 2019 12:53 am ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
Looking good. I have been looking at getting a USB socket and getting rid of the cigar lighter too. Like the idea of the ones with the voltage read out in them.

Author:	ArtistKS [ Thu Dec 05, 2019 9:07 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
Got variable intermittent wipers installed today Took me 2 days to do as couldn't figure out how to re install the new unit lol Very happy with it now. Here is a link to the video as the embed code doesn't seem to work https://imgur.com/4UmMbQi Installed a cone filter a few weeks ago Have yet to create a metal bracket to hold the cone filter more securely and so that it's a less ratchet setup lol Also, more big news. I finally have a name for my 323F! Dirty Angel The only inspiration I can point towards is the fact that she is always dirty and it was inspired by a song I really like. Dirty Angel by Airbourne. The name popped into my head when I was talking to a friend and referred to my car as 'in all her dirty glory' and here we are now. Up next, hopefully remote central locking and puddle lights.

Author:	HMT [ Fri Dec 06, 2019 4:24 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
Looking good mate, but i think you mounted the strut brace the wrong way around...

Author:	ArtistKS [ Fri Dec 06, 2019 6:41 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
Nope, that's the way it's meant to be. If it's the other way round the bonnet doesn't close.

Author:	maZZda [ Sat Dec 07, 2019 11:08 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
You should use some oil on that filter!It looks dry. Also it moves with the engine revving, do not tie it down to anything or it will eventually rip the filter apart from rubbing! For it's name the car looks overall pretty clean from my PC screen (you wash it before taking pictures, got ya!) The brace you put should be with the bigger bend to the right wheel top mount as you have already mount it once. What is the problem with the bonet not closing??

Author:	ArtistKS [ Sun Dec 08, 2019 8:29 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
The way it is in that photo is the correct way. The bonnet closes and the little notch in the bar is aligned perfectly with the intake manifold. In this photo it was put on the wrong way round and the bonnet wouldn't close with it like that.

Author:	maZZda [ Sun Dec 08, 2019 10:10 pm ]
Post subject:	Re: ArtistKS's 1996 1.5 BA
Now i see what i wrote early.. I meant that the biger bend on the brace should be at the right topmount while you stand infront of the car looking toward it.The battery side.. When i re-read it now, i understood that it could lead to confusion.. My bad.

Page 1 of 2	All times are UTC [ DST ]
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/